omap4/5: Add support for booting with CH.

Configuration header(CH) is 512 byte header attached to an OMAP
boot image that will help ROM code to initialize clocks, SDRAM
etc and copy U-Boot directly into SDRAM. CH can help us in
by-passing SPL and directly boot U-boot, hence it's an alternative
for SPL. However, we intend to support both CH and SPL for OMAP4/5.

Initialization done through CH is limited and is not equivalent
to that done by SPL. So U-Boot has to distinguish between the
two cases and handle them accordingly. This patch takes care
of doing this.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

arch/arm/cpu/armv7/omap-common/clocks-common.c

@@ -115,17 +115,46 @@ static inline void wait_for_lock(u32 *const base)
 	}
 }
 
-static void do_setup_dpll(u32 *const base, const struct dpll_params *params,
+inline u32 check_for_lock(u32 *const base)
-				u8 lock)
 {
-	u32 temp;
 	struct dpll_regs *const dpll_regs = (struct dpll_regs *)base;
+	u32 lock = readl(&dpll_regs->cm_idlest_dpll) & ST_DPLL_CLK_MASK;
+
+	return lock;
+}
+
+static void do_setup_dpll(u32 *const base, const struct dpll_params *params,
+				u8 lock, char *dpll)
+{
+	u32 temp, M, N;
+	struct dpll_regs *const dpll_regs = (struct dpll_regs *)base;
+
+	temp = readl(&dpll_regs->cm_clksel_dpll);
+
+	if (check_for_lock(base)) {
+		/*
+		 * The Dpll has already been locked by rom code using CH.
+		 * Check if M,N are matching with Ideal nominal opp values.
+		 * If matches, skip the rest otherwise relock.
+		 */
+		M = (temp & CM_CLKSEL_DPLL_M_MASK) >> CM_CLKSEL_DPLL_M_SHIFT;
+		N = (temp & CM_CLKSEL_DPLL_N_MASK) >> CM_CLKSEL_DPLL_N_SHIFT;
+		if ((M != (params->m)) || (N != (params->n))) {
+			debug("\n %s Dpll locked, but not for ideal M = %d,"
+				"N = %d values, current values are M = %d,"
+				"N= %d" , dpll, params->m, params->n,
+				M, N);
+		} else {
+			/* Dpll locked with ideal values for nominal opps. */
+			debug("\n %s Dpll already locked with ideal"
+						"nominal opp values", dpll);
+			goto setup_post_dividers;
+		}
+	}
 
 	bypass_dpll(base);
 
 	/* Set M & N */
-	temp = readl(&dpll_regs->cm_clksel_dpll);
-
 	temp &= ~CM_CLKSEL_DPLL_M_MASK;
 	temp |= (params->m << CM_CLKSEL_DPLL_M_SHIFT) & CM_CLKSEL_DPLL_M_MASK;
 
@@ -138,6 +167,7 @@ static void do_setup_dpll(u32 *const base, const struct dpll_params *params,
 	if (lock)
 		do_lock_dpll(base);
 
+setup_post_dividers:
 	setup_post_dividers(base, params);
 
 	/* Wait till the DPLL locks */
@@ -216,7 +246,8 @@ void configure_mpu_dpll(void)
 	}
 
 	params = get_mpu_dpll_params();
-	do_setup_dpll(&prcm->cm_clkmode_dpll_mpu, params, DPLL_LOCK);
+
+	do_setup_dpll(&prcm->cm_clkmode_dpll_mpu, params, DPLL_LOCK, "mpu");
 	debug("MPU DPLL locked\n");
 }
 
@@ -235,7 +266,8 @@ static void setup_dplls(void)
 	 * Core DPLL will be locked after setting up EMIF
 	 * using the FREQ_UPDATE method(freq_update_core())
 	 */
-	do_setup_dpll(&prcm->cm_clkmode_dpll_core, params, DPLL_NO_LOCK);
+	do_setup_dpll(&prcm->cm_clkmode_dpll_core, params, DPLL_NO_LOCK,
+								"core");
 	/* Set the ratios for CORE_CLK, L3_CLK, L4_CLK */
 	temp = (CLKSEL_CORE_X2_DIV_1 << CLKSEL_CORE_SHIFT) |
 	    (CLKSEL_L3_CORE_DIV_2 << CLKSEL_L3_SHIFT) |
@@ -246,13 +278,14 @@ static void setup_dplls(void)
 	/* lock PER dpll */
 	params = get_per_dpll_params();
 	do_setup_dpll(&prcm->cm_clkmode_dpll_per,
-			params, DPLL_LOCK);
+			params, DPLL_LOCK, "per");
 	debug("PER DPLL locked\n");
 
 	/* MPU dpll */
 	configure_mpu_dpll();
 }
 
+#ifdef CONFIG_SYS_CLOCKS_ENABLE_ALL
 static void setup_non_essential_dplls(void)
 {
 	u32 sys_clk_khz, abe_ref_clk;
@@ -267,7 +300,7 @@ static void setup_non_essential_dplls(void)
 		CM_BYPCLK_DPLL_IVA_CLKSEL_MASK, DPLL_IVA_CLKSEL_CORE_X2_DIV_2);
 
 	params = get_iva_dpll_params();
-	do_setup_dpll(&prcm->cm_clkmode_dpll_iva, params, DPLL_LOCK);
+	do_setup_dpll(&prcm->cm_clkmode_dpll_iva, params, DPLL_LOCK, "iva");
 
 	/*
 	 * USB:
@@ -287,7 +320,7 @@ static void setup_non_essential_dplls(void)
 			sd_div << CM_CLKSEL_DPLL_DPLL_SD_DIV_SHIFT);
 
 	/* Now setup the dpll with the regular function */
-	do_setup_dpll(&prcm->cm_clkmode_dpll_usb, params, DPLL_LOCK);
+	do_setup_dpll(&prcm->cm_clkmode_dpll_usb, params, DPLL_LOCK, "usb");
 
 	/* Configure ABE dpll */
 	params = get_abe_dpll_params();
@@ -315,8 +348,9 @@ static void setup_non_essential_dplls(void)
 			CM_ABE_PLL_REF_CLKSEL_CLKSEL_MASK,
 			abe_ref_clk << CM_ABE_PLL_REF_CLKSEL_CLKSEL_SHIFT);
 	/* Lock the dpll */
-	do_setup_dpll(&prcm->cm_clkmode_dpll_abe, params, DPLL_LOCK);
+	do_setup_dpll(&prcm->cm_clkmode_dpll_abe, params, DPLL_LOCK, "abe");
 }
+#endif
 
 void do_scale_tps62361(u32 reg, u32 volt_mv)
 {
@@ -561,10 +595,15 @@ void prcm_init(void)
 		enable_basic_clocks();
 		scale_vcores();
 		setup_dplls();
+#ifdef CONFIG_SYS_CLOCKS_ENABLE_ALL
 		setup_non_essential_dplls();
 		enable_non_essential_clocks();
+#endif
 		break;
 	default:
 		break;
 	}
+
+	if (OMAP_INIT_CONTEXT_SPL != omap_hw_init_context())
+		enable_basic_uboot_clocks();
 }

arch/arm/cpu/armv7/omap-common/hwinit-common.c

@@ -31,9 +31,18 @@
 #include <asm/arch/sys_proto.h>
 #include <asm/sizes.h>
 #include <asm/emif.h>
+#include <asm/omap_common.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
+/*
+ * This is used to verify if the configuration header
+ * was executed by rom code prior to control of transfer
+ * to the bootloader. SPL is responsible for saving and
+ * passing the boot_params pointer to the u-boot.
+ */
+struct omap_boot_parameters boot_params __attribute__ ((section(".data")));
+
 #ifdef CONFIG_SPL_BUILD
 /*
  * We use static variables because global data is not ready yet.
@@ -41,12 +50,11 @@ DECLARE_GLOBAL_DATA_PTR;
  * We would not typically need to save these parameters in regular
  * U-Boot. This is needed only in SPL at the moment.
  */
-u32 omap_bootdevice = BOOT_DEVICE_MMC1;
 u32 omap_bootmode = MMCSD_MODE_FAT;
 
 u32 omap_boot_device(void)
 {
-	return omap_bootdevice;
+	return (u32) (boot_params.omap_bootdevice);
 }
 
 u32 omap_boot_mode(void)
@@ -71,12 +79,16 @@ static void set_mux_conf_regs(void)
 		set_muxconf_regs_essential();
 		break;
 	case OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL:
+#ifdef CONFIG_SYS_ENABLE_PADS_ALL
 		set_muxconf_regs_non_essential();
+#endif
 		break;
 	case OMAP_INIT_CONTEXT_UBOOT_FROM_NOR:
 	case OMAP_INIT_CONTEXT_UBOOT_AFTER_CH:
 		set_muxconf_regs_essential();
+#ifdef CONFIG_SYS_ENABLE_PADS_ALL
 		set_muxconf_regs_non_essential();
+#endif
 		break;
 	}
 }
@@ -103,6 +115,13 @@ void omap_rev_string(char *omap_rev_string)
 		minor_rev);
 }
 
+#ifdef CONFIG_SPL_BUILD
+static void init_boot_params(void)
+{
+	boot_params_ptr = (u32 *) &boot_params;
+}
+#endif
+
 /*
  * Routine: s_init
  * Description: Does early system init of watchdog, muxing,  andclocks
@@ -131,6 +150,7 @@ void s_init(void)
 #ifdef CONFIG_SPL_BUILD
 	/* For regular u-boot sdram_init() is called from dram_init() */
 	sdram_init();
+	init_boot_params();
 #endif
 }
 

arch/arm/cpu/armv7/omap-common/lowlevel_init.S

@@ -27,7 +27,7 @@
  */
 
 #include <asm/arch/omap.h>
-#ifdef CONFIG_SPL_BUILD
+
 .global save_boot_params
 save_boot_params:
 	/*
@@ -43,21 +43,40 @@ save_boot_params:
 	cmp	r2, r0
 	blt	1f
 
+	/*
+	 * store the boot params passed from rom code or saved
+	 * and passed by SPL
+	 */
+	cmp	r0, #0
+	beq	1f
+	ldr	r1, =boot_params
+	str	r0, [r1]
+#ifdef CONFIG_SPL_BUILD
 	/* Store the boot device in omap_boot_device */
-	ldr     r2, [r0, #BOOT_DEVICE_OFFSET]	@ r1 <- value of boot device
+	ldrb	r2, [r0, #BOOT_DEVICE_OFFSET]	@ r1 <- value of boot device
 	and	r2, #BOOT_DEVICE_MASK
-	ldr	r3, =omap_bootdevice
+	ldr	r3, =boot_params
-	str     r2, [r3]			@ omap_boot_device <- r1
+	strb	r2, [r3, #BOOT_DEVICE_OFFSET]	@ omap_boot_device <- r1
 
+	/* boot mode is passed only for devices that can raw/fat mode */
+	cmp	r2, #2
+	blt	2f
+	cmp	r2, #7
+	bgt	2f
 	/* Store the boot mode (raw/FAT) in omap_boot_mode */
 	ldr	r2, [r0, #DEV_DESC_PTR_OFFSET]	@ get the device descriptor ptr
 	ldr	r2, [r2, #DEV_DATA_PTR_OFFSET]	@ get the pDeviceData ptr
 	ldr	r2, [r2, #BOOT_MODE_OFFSET]	@ get the boot mode
 	ldr	r3, =omap_bootmode
 	str	r2, [r3]
+#endif
+2:
+	ldrb	r2, [r0, #CH_FLAGS_OFFSET]
+	ldr	r3, =boot_params
+	strb	r2, [r3, #CH_FLAGS_OFFSET]
 1:
 	bx	lr
-#endif
+
 
 .globl lowlevel_init
 lowlevel_init:

arch/arm/cpu/armv7/omap-common/spl.c

@@ -38,6 +38,7 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
+u32* boot_params_ptr = NULL;
 struct spl_image_info spl_image;
 
 /* Define global data structure pointer to it*/
@@ -92,12 +93,16 @@ void spl_parse_image_header(const struct image_header *header)
 
 static void jump_to_image_no_args(void)
 {
-	typedef void (*image_entry_noargs_t)(void)__attribute__ ((noreturn));
+	typedef void (*image_entry_noargs_t)(u32 *)__attribute__ ((noreturn));
 	image_entry_noargs_t image_entry =
 			(image_entry_noargs_t) spl_image.entry_point;
 
 	debug("image entry point: 0x%X\n", spl_image.entry_point);
-	image_entry();
+	/* Pass the saved boot_params from rom code */
+#if defined(CONFIG_VIRTIO) || defined(CONFIG_ZEBU)
+	image_entry = 0x80100000;
+#endif
+	image_entry((u32 *)&boot_params_ptr);
 }
 
 void jump_to_image_no_args(void) __attribute__ ((noreturn));

arch/arm/cpu/armv7/omap4/clocks.c

@@ -333,30 +333,23 @@ void enable_basic_clocks(void)
 	};
 
 	u32 *const clk_modules_hw_auto_essential[] = {
+		&prcm->cm_memif_emif_1_clkctrl,
+		&prcm->cm_memif_emif_2_clkctrl,
+		&prcm->cm_l4cfg_l4_cfg_clkctrl,
 		&prcm->cm_wkup_gpio1_clkctrl,
 		&prcm->cm_l4per_gpio2_clkctrl,
 		&prcm->cm_l4per_gpio3_clkctrl,
 		&prcm->cm_l4per_gpio4_clkctrl,
 		&prcm->cm_l4per_gpio5_clkctrl,
 		&prcm->cm_l4per_gpio6_clkctrl,
-		&prcm->cm_memif_emif_1_clkctrl,
-		&prcm->cm_memif_emif_2_clkctrl,
-		&prcm->cm_l3init_hsusbotg_clkctrl,
-		&prcm->cm_l3init_usbphy_clkctrl,
-		&prcm->cm_l4cfg_l4_cfg_clkctrl,
 		0
 	};
 
 	u32 *const clk_modules_explicit_en_essential[] = {
-		&prcm->cm_l4per_gptimer2_clkctrl,
+		&prcm->cm_wkup_gptimer1_clkctrl,
 		&prcm->cm_l3init_hsmmc1_clkctrl,
 		&prcm->cm_l3init_hsmmc2_clkctrl,
-		&prcm->cm_l4per_mcspi1_clkctrl,
+		&prcm->cm_l4per_gptimer2_clkctrl,
-		&prcm->cm_wkup_gptimer1_clkctrl,
-		&prcm->cm_l4per_i2c1_clkctrl,
-		&prcm->cm_l4per_i2c2_clkctrl,
-		&prcm->cm_l4per_i2c3_clkctrl,
-		&prcm->cm_l4per_i2c4_clkctrl,
 		&prcm->cm_wkup_wdtimer2_clkctrl,
 		&prcm->cm_l4per_uart3_clkctrl,
 		0
@@ -386,6 +379,33 @@ void enable_basic_clocks(void)
 			 1);
 }
 
+void enable_basic_uboot_clocks(void)
+{
+	u32 *const clk_domains_essential[] = {
+		0
+	};
+
+	u32 *const clk_modules_hw_auto_essential[] = {
+		&prcm->cm_l3init_hsusbotg_clkctrl,
+		&prcm->cm_l3init_usbphy_clkctrl,
+		0
+	};
+
+	u32 *const clk_modules_explicit_en_essential[] = {
+		&prcm->cm_l4per_mcspi1_clkctrl,
+		&prcm->cm_l4per_i2c1_clkctrl,
+		&prcm->cm_l4per_i2c2_clkctrl,
+		&prcm->cm_l4per_i2c3_clkctrl,
+		&prcm->cm_l4per_i2c4_clkctrl,
+		0
+	};
+
+	do_enable_clocks(clk_domains_essential,
+			 clk_modules_hw_auto_essential,
+			 clk_modules_explicit_en_essential,
+			 1);
+}
+
 /*
  * Enable non-essential clock domains, modules and
  * do some additional special settings needed

arch/arm/cpu/armv7/omap5/clocks.c

@@ -273,30 +273,26 @@ void enable_basic_clocks(void)
 	};
 
 	u32 *const clk_modules_hw_auto_essential[] = {
+		&prcm->cm_memif_emif_1_clkctrl,
+		&prcm->cm_memif_emif_2_clkctrl,
+		&prcm->cm_l4cfg_l4_cfg_clkctrl,
 		&prcm->cm_wkup_gpio1_clkctrl,
 		&prcm->cm_l4per_gpio2_clkctrl,
 		&prcm->cm_l4per_gpio3_clkctrl,
 		&prcm->cm_l4per_gpio4_clkctrl,
 		&prcm->cm_l4per_gpio5_clkctrl,
 		&prcm->cm_l4per_gpio6_clkctrl,
-		&prcm->cm_memif_emif_1_clkctrl,
-		&prcm->cm_memif_emif_2_clkctrl,
-		&prcm->cm_l4cfg_l4_cfg_clkctrl,
 		0
 	};
 
 	u32 *const clk_modules_explicit_en_essential[] = {
-		&prcm->cm_l4per_gptimer2_clkctrl,
+		&prcm->cm_wkup_gptimer1_clkctrl,
 		&prcm->cm_l3init_hsmmc1_clkctrl,
 		&prcm->cm_l3init_hsmmc2_clkctrl,
-		&prcm->cm_l4per_mcspi1_clkctrl,
+		&prcm->cm_l4per_gptimer2_clkctrl,
-		&prcm->cm_wkup_gptimer1_clkctrl,
-		&prcm->cm_l4per_i2c1_clkctrl,
-		&prcm->cm_l4per_i2c2_clkctrl,
-		&prcm->cm_l4per_i2c3_clkctrl,
-		&prcm->cm_l4per_i2c4_clkctrl,
 		&prcm->cm_wkup_wdtimer2_clkctrl,
 		&prcm->cm_l4per_uart3_clkctrl,
+		&prcm->cm_l4per_i2c1_clkctrl,
 		0
 	};
 
@@ -320,6 +316,30 @@ void enable_basic_clocks(void)
 			 1);
 }
 
+void enable_basic_uboot_clocks(void)
+{
+	u32 *const clk_domains_essential[] = {
+		0
+	};
+
+	u32 *const clk_modules_hw_auto_essential[] = {
+		0
+	};
+
+	u32 *const clk_modules_explicit_en_essential[] = {
+		&prcm->cm_l4per_mcspi1_clkctrl,
+		&prcm->cm_l4per_i2c2_clkctrl,
+		&prcm->cm_l4per_i2c3_clkctrl,
+		&prcm->cm_l4per_i2c4_clkctrl,
+		0
+	};
+
+	do_enable_clocks(clk_domains_essential,
+			 clk_modules_hw_auto_essential,
+			 clk_modules_explicit_en_essential,
+			 1);
+}
+
 /*
  * Enable non-essential clock domains, modules and
  * do some additional special settings needed

arch/arm/include/asm/arch-omap4/clocks.h

@@ -698,6 +698,7 @@ void setup_sri2c(void);
 void setup_post_dividers(u32 *const base, const struct dpll_params *params);
 u32 get_sys_clk_index(void);
 void enable_basic_clocks(void);
+void enable_basic_uboot_clocks(void);
 void enable_non_essential_clocks(void);
 void do_enable_clocks(u32 *const *clk_domains,
 		      u32 *const *clk_modules_hw_auto,

arch/arm/include/asm/arch-omap4/omap.h

@@ -191,5 +191,21 @@ struct control_lpddr2io_regs {
 #define DEV_DESC_PTR_OFFSET	0x4
 #define DEV_DATA_PTR_OFFSET	0x18
 #define BOOT_MODE_OFFSET	0x8
+#define RESET_REASON_OFFSET	0x9
+#define CH_FLAGS_OFFSET		0xA
 
+#define CH_FLAGS_CHSETTINGS	(0x1 << 0)
+#define CH_FLAGS_CHRAM		(0x1 << 1)
+#define CH_FLAGS_CHFLASH	(0x1 << 2)
+#define CH_FLAGS_CHMMCSD	(0x1 << 3)
+
+#ifndef __ASSEMBLY__
+struct omap_boot_parameters {
+	char *boot_message;
+	unsigned int mem_boot_descriptor;
+	unsigned char omap_bootdevice;
+	unsigned char reset_reason;
+	unsigned char ch_flags;
+};
+#endif
 #endif

arch/arm/include/asm/arch-omap4/sys_proto.h

@@ -55,6 +55,13 @@ u32 omap_sdram_size(void);
 u32 cortex_rev(void);
 void init_omap_revision(void);
 void do_io_settings(void);
+/*
+ * This is used to verify if the configuration header
+ * was executed by Romcode prior to control of transfer
+ * to the bootloader. SPL is responsible for saving and
+ * passing this to the u-boot.
+ */
+extern struct omap_boot_parameters boot_params;
 
 static inline u32 running_from_sdram(void)
 {
@@ -67,14 +74,16 @@ static inline u32 running_from_sdram(void)
 static inline u8 uboot_loaded_by_spl(void)
 {
 	/*
-	 * Configuration Header is not supported yet, so u-boot init running
+	 * u-boot can be running from sdram either because of configuration
-	 * from SDRAM implies that it was loaded by SPL. When this situation
+	 * Header or by SPL. If because of CH, then the romcode sets the
-	 * changes one of these approaches could be taken:
+	 * CHSETTINGS executed bit to true in the boot parameter structure that
-	 * i.  Pass a magic from SPL to U-Boot and U-Boot save it at a known
+	 * it passes to the bootloader.This parameter is stored in the ch_flags
-	 *     location.
+	 * variable by both SPL and u-boot.Check out for CHSETTINGS, which is a
-	 * ii. Check the OPP. CH can support only 50% OPP while SPL initializes
+	 * mandatory section if CH is present.
-	 *     the DPLLs at 100% OPP.
 	 */
+	if ((boot_params.ch_flags) & (CH_FLAGS_CHSETTINGS))
+		return 0;
+	else
 		return running_from_sdram();
 }
 /*

arch/arm/include/asm/arch-omap5/clocks.h

@@ -708,6 +708,7 @@ void setup_post_dividers(u32 *const base, const struct dpll_params *params);
 u32 get_sys_clk_index(void);
 void enable_basic_clocks(void);
 void enable_non_essential_clocks(void);
+void enable_basic_uboot_clocks(void);
 void do_enable_clocks(u32 *const *clk_domains,
 		      u32 *const *clk_modules_hw_auto,
 		      u32 *const *clk_modules_explicit_en,

arch/arm/include/asm/arch-omap5/omap.h

@@ -203,5 +203,21 @@ struct control_lpddr2io_regs {
 #define DEV_DESC_PTR_OFFSET	0x4
 #define DEV_DATA_PTR_OFFSET	0x18
 #define BOOT_MODE_OFFSET	0x8
+#define RESET_REASON_OFFSET     0x9
+#define CH_FLAGS_OFFSET         0xA
 
+#define CH_FLAGS_CHSETTINGS	(0x1 << 0)
+#define	CH_FLAGS_CHRAM		(0x1 << 1)
+#define CH_FLAGS_CHFLASH	(0x1 << 2)
+#define CH_FLAGS_CHMMCSD	(0x1 << 3)
+
+#ifndef __ASSEMBLY__
+struct omap_boot_parameters {
+	char *boot_message;
+	unsigned int mem_boot_descriptor;
+	unsigned char omap_bootdevice;
+	unsigned char reset_reason;
+	unsigned char ch_flags;
+};
+#endif /* __ASSEMBLY__ */
 #endif

arch/arm/include/asm/arch-omap5/sys_proto.h

@@ -75,14 +75,16 @@ static inline u32 running_from_sdram(void)
 static inline u8 uboot_loaded_by_spl(void)
 {
 	/*
-	 * Configuration Header is not supported yet, so u-boot init running
+	 * u-boot can be running from sdram either because of configuration
-	 * from SDRAM implies that it was loaded by SPL. When this situation
+	 * Header or by SPL. If because of CH, then the romcode sets the
-	 * changes one of these approaches could be taken:
+	 * CHSETTINGS executed bit to true in the boot parameter structure that
-	 * i.  Pass a magic from SPL to U-Boot and U-Boot save it at a known
+	 * it passes to the bootloader.This parameter is stored in the ch_flags
-	 *     location.
+	 * variable by both SPL and u-boot.Check out for CHSETTINGS, which is a
-	 * ii. Check the OPP. CH can support only 50% OPP while SPL initializes
+	 * mandatory section if CH is present.
-	 *     the DPLLs at 100% OPP.
 	 */
+	if ((boot_params.ch_flags) & (CH_FLAGS_CHSETTINGS))
+		return 0;
+	else
 		return running_from_sdram();
 }
 /*

arch/arm/include/asm/omap_common.h

@@ -80,6 +80,7 @@ struct spl_image_info {
 
 extern struct spl_image_info spl_image;
 
+extern u32* boot_params_ptr;
 u32 omap_boot_device(void);
 u32 omap_boot_mode(void);
 

board/ti/omap5_evm/mux_data.h

@@ -50,14 +50,6 @@ const struct pad_conf_entry core_padconf_array_essential[] = {
 {SDMMC1_DAT5, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat5 */
 {SDMMC1_DAT6, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat6 */
 {SDMMC1_DAT7, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat7 */
-{I2C1_SCL, (PTU | IEN | M0)},				/* i2c1_scl */
-{I2C1_SDA, (PTU | IEN | M0)},				/* i2c1_sda */
-{I2C2_SCL, (PTU | IEN | M0)},				/* i2c2_scl */
-{I2C2_SDA, (PTU | IEN | M0)},				/* i2c2_sda */
-{I2C3_SCL, (PTU | IEN | M0)},				/* i2c3_scl */
-{I2C3_SDA, (PTU | IEN | M0)},				/* i2c3_sda */
-{I2C4_SCL, (PTU | IEN | M0)},				/* i2c4_scl */
-{I2C4_SDA, (PTU | IEN | M0)},				/* i2c4_sda */
 {UART3_CTS_RCTX, (PTU | IEN | M0)},			/* uart3_tx */
 {UART3_RTS_SD, (M0)},					/* uart3_rts_sd */
 {UART3_RX_IRRX, (IEN | M0)},				/* uart3_rx */
@@ -245,6 +237,14 @@ const struct pad_conf_entry core_padconf_array_non_essential[] = {
 	{DPM_EMU17, (IEN | M5)},					/* dispc2_data2 */
 	{DPM_EMU18, (IEN | M5)},					/* dispc2_data1 */
 	{DPM_EMU19, (IEN | M5)},					/* dispc2_data0 */
+	{I2C1_SCL, (PTU | IEN | M0)},				/* i2c1_scl */
+	{I2C1_SDA, (PTU | IEN | M0)},				/* i2c1_sda */
+	{I2C2_SCL, (PTU | IEN | M0)},				/* i2c2_scl */
+	{I2C2_SDA, (PTU | IEN | M0)},				/* i2c2_sda */
+	{I2C3_SCL, (PTU | IEN | M0)},				/* i2c3_scl */
+	{I2C3_SDA, (PTU | IEN | M0)},				/* i2c3_sda */
+	{I2C4_SCL, (PTU | IEN | M0)},				/* i2c4_scl */
+	{I2C4_SDA, (PTU | IEN | M0)}				/* i2c4_sda */
 };
 
 const struct pad_conf_entry wkup_padconf_array_non_essential[] = {

board/ti/sdp4430/sdp4430_mux_data.h

@@ -50,14 +50,6 @@ const struct pad_conf_entry core_padconf_array_essential[] = {
 {SDMMC1_DAT5, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat5 */
 {SDMMC1_DAT6, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat6 */
 {SDMMC1_DAT7, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat7 */
-{I2C1_SCL, (PTU | IEN | M0)},				/* i2c1_scl */
-{I2C1_SDA, (PTU | IEN | M0)},				/* i2c1_sda */
-{I2C2_SCL, (PTU | IEN | M0)},				/* i2c2_scl */
-{I2C2_SDA, (PTU | IEN | M0)},				/* i2c2_sda */
-{I2C3_SCL, (PTU | IEN | M0)},				/* i2c3_scl */
-{I2C3_SDA, (PTU | IEN | M0)},				/* i2c3_sda */
-{I2C4_SCL, (PTU | IEN | M0)},				/* i2c4_scl */
-{I2C4_SDA, (PTU | IEN | M0)},				/* i2c4_sda */
 {UART3_CTS_RCTX, (PTU | IEN | M0)},			/* uart3_tx */
 {UART3_RTS_SD, (M0)},					/* uart3_rts_sd */
 {UART3_RX_IRRX, (IEN | M0)},				/* uart3_rx */
@@ -251,6 +243,15 @@ const struct pad_conf_entry core_padconf_array_non_essential[] = {
 	{DPM_EMU17, (IEN | M5)},					/* dispc2_data2 */
 	{DPM_EMU18, (IEN | M5)},					/* dispc2_data1 */
 	{DPM_EMU19, (IEN | M5)},					/* dispc2_data0 */
+	{I2C1_SCL, (PTU | IEN | M0)},					/* i2c1_scl */
+	{I2C1_SDA, (PTU | IEN | M0)},					/* i2c1_sda */
+	{I2C2_SCL, (PTU | IEN | M0)},					/* i2c2_scl */
+	{I2C2_SDA, (PTU | IEN | M0)},					/* i2c2_sda */
+	{I2C3_SCL, (PTU | IEN | M0)},					/* i2c3_scl */
+	{I2C3_SDA, (PTU | IEN | M0)},					/* i2c3_sda */
+	{I2C4_SCL, (PTU | IEN | M0)},					/* i2c4_scl */
+	{I2C4_SDA, (PTU | IEN | M0)}					/* i2c4_sda */
+
 };
 
 const struct pad_conf_entry wkup_padconf_array_non_essential[] = {

include/configs/omap4_common.h

@@ -122,6 +122,9 @@
 /* Flash */
 #define CONFIG_SYS_NO_FLASH	1
 
+/* clocks */
+#define CONFIG_SYS_CLOCKS_ENABLE_ALL
+
 /* commands to include */
 #include <config_cmd_default.h>
 
@@ -278,4 +281,6 @@
 #define CONFIG_SPL_SERIAL_SUPPORT
 #define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/omap-common/u-boot-spl.lds"
 
+#define CONFIG_SYS_ENABLE_PADS_ALL
+
 #endif /* __CONFIG_OMAP4_COMMON_H */