This file has been synced (copy) from Linux source code.
This commit was based on kernel 2.6.32.
It updates gigabit related phy registers and basic definitions.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Recent cleanup actions resulted in a number of config.mk files that
contained only LDSCRIPT definitions. Move these into th respective
board config files and remove the now empty config.mk files.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andre Schwarz <andre.schwarz@matrix-vision.de>
Cc: Peter De Schrijver <p2@mind.be>
Acked-by: Detlev Zundel < dzu@denx.de>
Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Heiko Schocher<hs@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
This board uses the OMAP-L138 SOM stacked on a
custom baseboard. It supports SPI Flash, Ethernet
with RMII.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch is a port of the work by Sudhakar Rajeshekhara in commit
ab3effbcad8851cc65dc5241a01c064d2030a3b2 of
git://arago-project.org/git/people/sandeep/u-boot-davinci.git.
The da850 UI board has on it an RMII PHY which can be used if the MDC line
to the MII PHY on the baseboard is disabled and the RMII PHY is enabled by
configuring the values of some GPIO pins on the IO expander of the UI board.
This patch implements disabling that line via GPIO2[6], configuring the UI
board's IO expander and setting only the pinmux settings that are needed for
RMII operation.
Tested on da850evm by adding a define for CONFIG_DRIVER_TI_EMAC_USE_RMII.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The patch adds basic board support for TI's OMAP-L138 based
Hawkboard. This board is pretty similar to the da850 EVM. Support for
nand and network access is added in this version.
The following bootup procedure is used.
At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand
controllers and copies the second stage bootloader(nand_spl) to
RAM. The secondary bootloader then copies u-boot from a predefined
location in the nand flash to the RAM, and passes control to the
u-boot image.
Three config options are supported
* hawkboard_config - Used to create the u-boot.bin. Tftp the
u-boot.bin image to the RAM from u-boot, and flash to the nand flash
at address 0xe0000.
* hawkboard_nand_config - Used to generate the secondary
bootloader(nand_spl) image. This creates an elf file u-boot-spl
under nand_spl/. Create an AIS signed image using this file, and
flash it to the nand flash at address 0x20000. The ais file should
fit in one block.
* hawkboard_uart_config - This is same as the first image, but with
the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The patch was already posted to the arago project,
but not yet to mainline. It allows to save environment into
the spi flash. Tested on LogiPD tmdxl138.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Detlev Zundev <dzu@denx.de>
CC: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Currently the hardware was left in an undefined state in case Spartan3
serial load failed. This patch adds Xilinx_abort_fn to give the board
a possibility to clean up in this case.
Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
Reuse the gd->tbl value for timestamp and add gd->lastinc for lastinc
bss values in arm920t/at91/timer driver.
The usage of bss values in driver before initialisation of bss is
forbidden. In that special case some data in .rel.dyn gets corrupted by
the arm920t/at91/timer driver.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch also removes now unnecessary config.mk in board directory and
make usage of new features in boards.cfg.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Adds support for the EMK TOP9000 CPU Module which is
based on ATMELs ARM926EJS AT91SAM9XE SoC.
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
CONFIG_FSL_DIU_LOGO_BMP has been removed while refactoring
MPC8610 and MPC5121 DIU code, so remove it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
We intended to use the PIC TFRR register however we where missing adding
in the PIC register base offset from IMMR when we defined
_POST_WORD_ADDR.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some systems need to relocate the env_addr pointer early because the
location it points to will get invalidated before env_relocate is
called. One example is on systems that might use a L2 or L3 cache
in SRAM mode and initialize that cache from SRAM mode back to being
a cache in cpu_init_r.
We set this on the 85xx boards that have support for NAND, SPI, or
SDHC/MMC boot support as they use a secondary cache in SRAM mode and
need the env_addr pointer relocated since we change from SRAM to normal
cache mode in cpu_init_r.
Also removed CONFIG_SYS_SPL as its not used anywhere.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Changed the CS4 and CS5 addresses on Local Bus for matching the PMC0
and PMC1 addresses.
Signed-off-by: Stefan Popa <Stefan.Popa@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Without CONFIG_CMD_NET support CONFIG_CMD_NFS leads
to linking error, so disable CONFIG_CMD_NFS option.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Also change the CONFIG_SYS_TEXT_BASE to 0x80008000, required
with relocation support. This is the load address for primary
boot loader (x-loader).
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The macro CONFIG_SYS_GBL_DATA_SIZE has been replaced
with GENERATED_GBL_DATA_SIZE.
Also define macros: CONFIG_SYS_INIT_RAM_ADDR and
CONFIG_SYS_INIT_RAM_SIZE.
Based on changes for omap3_beagle in the commit:
31bfcf1c5776df3d90286aa15104c45096d53dc6
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Seems that if CONFIG_CMD_NET is undefined we should also
undefine CONFIG_CMD_NFS, otherwise build fails with various
undefined reference like:
net/libnet.o: In function `rpc_req':
u-boot/net/nfs.c:193: undefined reference to `NetEthHdrSize'
u-boot/net/nfs.c:202: undefined reference to `NetSendUDPPacket'
u-boot/net/nfs.c:203: undefined reference to `NetTxPacket'
u-boot/net/nfs.c:203: undefined reference to `NetServerEther'
This patch adds the undef CONFIG_CMD_NFS in configuration file.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch fixes the SDB4430 build after commit 6d8962e814c15807dd6ac5757904be2a02d187b8
by explicitly disabling CMD_NFS.
>From the commit message for "Switch from archive libraries to partial linking":
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Two configuration include files had duplicate CONFIG_DOS_PARTITION
definitions with the same value.
This patch does not effect anything, just trims unnecessary text.
Signed-off-by: Semih Hazar <semih.hazar@indefia.com>
Rather than add runtime overhead of installing completion handlers, do it
statically at build time. This requires a new build time helper macro to
declare a command and the completion handler at the same time. Then we
convert the env related funcs over to this.
This gives an opportunity to also unify the U_BOOT_CMD macros.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The duplication of the do_reset prototype has gotten out of hand,
and they're not all in sync. Unify them all in command.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The duplication of the do_bootm prototype has gotten out of hand,
and they're pretty much all outdated (wrt constness). Unify them
all in command.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The recent command clean up to constify the argv option to command funcs
missed the command_t type itself. This is probably because there are no
build time warnings from it because no one is actually using this thing.
So just punt it rather than fix it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
