1) Change the i.MX serial driver to use the baud rate set in the
u-boot environment
2) don't assume a 16MHz value for PERCLK1 in baud rate calculations
3) don't write a 1 to the RDR bit in the USR2 reg. (bit is not "write
one to clear" like other status bits in the reg.)
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
Code in cpu/arm920t/start.S will die with a compilation error if
CONFIG_STACKSIZE + CFG_MALLOC_LEN works out to an invalid constant for
the ARM sub instruction. Change the code so that each is subtracted
independently to avoid the error.
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
This patch adds the reset_timer() function (needed by nand_base.c) and
modifies the get_timer_masked() to work in the same way as the omap24xx
function.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Based on original patch by Bernard Blackham <bernard@largestprime.net>
U-boot's HW ECC support for large page NAND on Davinci is completely
broken. Some kernels, such as the 2.6.10 one supported by
MontaVista for DaVinci, rely upon this broken behaviour as they
share the same code for ECCs. In the existing scheme, error
detection *might* work on large page, but error correction
definitely does not. Small page ECC correction works, but the
format is not compatible with the mainline git kernel.
This patch adds ECC code that matches what is currently in the
Davinci git repository (since NAND support was added in 2.6.24).
This makes the ECC and OOB layout written by u-boot compatible with
Linux for both small page and large page devices and fixes ECC
correction for large page devices.
The old behaviour can be restored by defining the macro
CFG_DAVINCI_BROKEN_ECC, which is undefined by default.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Acked-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Fix printf format-string/arg mismatches under -DDEBUG.
These warnings occur with DEBUG defined for a platform using
cpu/mpc85xx. Users of other architectures can unearth similar
problems by adding the line "CFLAGS += -DDEBUG=1" in config.mk right
after "CFLAGS += $(call cc-option,-fno-stack-protector)".
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The e500um says the timebase is volatile out of reset. To ensure
TB sync works we need to make sure its zero.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes warnings like this:
start.S:0: warning: target CPU does not support interworking
which come from some ARM cross compilers and are caused by hard-coded
(with "--with-cpu=arm9" configuration option) ARM targets (which
support ARM Thumb instructions), while the ARM target selected from
the command line (with "-march=armv4") doesn't support Thumb
instructions.
This warning is issued by the compiler regardless of the real use of
the Thumb instructions in code.
To fix this problem, we use options according to compiler version
being used.
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Since this define is only used on one board that was never really in
production, removing this compile time option doesn't hurt and makes
the code more readable.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a compilation warning for the PIP405 board. It moves the
#ifndef CONFIG_CS8952_PHY define a little so that the warning doesn't
occur anymore. I am a little unsure if this #ifdef is at the correct
place now or if it could be removed completely. This needs to get
tested on the PIP405 board.
Signed-off-by: Stefan Roese <sr@denx.de>
ctrl_regs.c: In function 'compute_fsl_memctl_config_regs':
ctrl_regs.c:523: warning: 'caslat' may be used uninitialized in this function
ctrl_regs.c:523: note: 'caslat' was declared here
Add a warning in DDR1 case if cas_latency isn't a value we know about.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds GPCS, SGMII and M88E1112 PHY support
for the AMCC PPC460GT/EX processors.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Alternate SDRAM DDR autocalibration routine that can be generically used
for any PPC4xx chips that have the IBM SDRAM Controller core allowing for
support of more DIMM/memory chip vendors and gets the DDR autocalibration
values which give the best read latency performance (SDRAM0_RDCC.[RDSS]).
Two alternate SDRAM DDR autocalibration algoritm are provided in this patch,
"Method_A" and "Method_B". DDR autocalibration Method_A scans the full range
of possible PPC4xx SDRAM Controller DDR autocalibration values and takes a
lot longer to run than Method_B. Method_B executes in the same amount of time
as the currently existing DDR autocalibration routine, i.e. 1 second or so.
Normally Method_B is used and it is set as the default method.
The current U-Boot PPC4xx DDR autocalibration code calibrates the IBM SDRAM
Controller registers.[bit-field]:
1) SDRAM0_RQDC.[RQFD]
2) SDRAM0_RFDC.[RFFD]
This alternate PPC4xx DDR autocalibration code calibrates the following
IBM SDRAM Controller registers.[bit-field]:
1) SDRAM0_WRDTR.[WDTR]
2) SDRAM0_CLKTR.[CKTR]
3) SDRAM0_RQDC.[RQFD]
4) SDRAM0_RFDC.[RFFD]
and will also use the calibrated settings of the above four registers that
produce the best "Read Sample Cycle Select" value in the SDRAM0_RDCC.[RDSS]
register.[bit-field].
Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cleans up some latent issues with the data cache control so that
dcache_enable() and dcache_disable() will work reliably (after
unlock_ram_in_cache() has been called)
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Record the Arbiter Event Register values and optionally display them.
The Arbiter Event Register can record the type and effective address of
an arbiter error, even through an HRESET. This patch stores the values in
the global data structure.
Display of the Arbiter Event registers immediately after the RSR value
can be enabled with defines. The Arbiter values will only be displayed
if an arbiter event has occured since the last Power On Reset, and either
of the following defines exist:
#define CONFIG_DISPLAY_AER_BRIEF - display only the arbiter address and
and type register values
#define CONFIG_DISPLAY_AER_FULL - display and interpret the arbiter
event register values
Address Only transactions are one of the trapped events that can register
as an arbiter event. They occur with some cache manipulation instructions
if the HID0_ABE (Address Broadcast Enable) is set and the memory region
has the MEMORY_COHERENCE WIMG bit set. Setting:
#define CONFIG_MASK_AER_AO - prevents the arbiter from recording address
only events, so that it can still capture
other real problems.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This is needed in unlock_ram_in_cache() because it is called from C and
will corrupt the small data area anchor that is kept in R2.
lock_ram_in_cache() is modified similarly as good coding practice, but
is not called from C.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Set DAT value before DIR values to avoid creating glitches on the
GPIO signals.
Set gpio level register before direction register to inhibit
glitches on high level output pins.
Dir and data gets cleared at powerup, so high level output lines see
a short low pulse between setting the direction and level registers.
Issue was seen on a new board with the nReset line of the NOR flash
connected to a GPIO. Setting the direction register puts the NOR flash
in reset so the next instruction to set the level cannot get executed.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Modified board_eth_init() functions of boards that have this FEC in addition
to other Ethernet controllers.
Affected boards:
bc3450
icecube
mvbc_p
o2dnt
pm520
total5200
tq5200
Removed initialization of controller from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This addresses all drivers whose initializers have already
been moved to board_eth_init()/cpu_eth_init().
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The tsec driver contains a hard-coded array of configuration information
for the tsec ethernet controllers. We create a default function that works
for most tsecs, and allow that to be overridden by board code. It creates
an array of tsec_info structures, which are then parsed by the corresponding
driver instance to determine configuration. Also, add regs, miiregs, and
devname fields to the tsec_info structure, so that we don't need the kludgy
"index" parameter.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The "GPIO" port mux is used on AVR32 UC3 parts as well as AT32AP7200 and
all later AVR32 chips. This patch adds a driver for it, implementing the
same API as the existing portmux-pio driver but with more functionality.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Replace the avr32-specific gclk_init() board hook with the standard
board_postclk_init() hook which is supposed to run at the same point
during initialization.
Provide a dummy weak alias for boards not implementing this hook. The
cost of this is:
- 2 bytes for the dummy function (retal 0)
- 2 bytes for each unnecessary function call (short rcall)
which is a pretty small price to pay for avoiding lots of #ifdef
clutter. In this particular case, all boards probably end up slightly
smaller because we avoid the conditional checking if the gclk_init
symbol is NULL.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Add two helper functions for configuring and enabling generic clocks:
- gclk_enable_output: Enables output on a GCLKx pin
- gclk_set_rate: Configures a gclk to run at a specific rate
This should eliminate any reason to go mucking about with PM registers
from board code.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
- Separate the portmux configuration functionality from the GPIO pin
control API.
- Separate the controller-specific code from the chip-specific code.
- Allow "ganged" port configuration (multiple pins at once).
- Add more flexibility to the "canned" peripheral select functions:
- Allow using more than 23 address bits, more chip selects, as
well as NAND- and CF-specific pins.
- Make the MACB SPEED pin optional, and choose between MII/RMII
using a parameter instead of an #ifdef.
- Make it possible to use other MMC slots than slot 0, and support
different MMC/SDCard data bus widths.
- Use more reasonable pull-up defaults; floating pins may consume a
lot of power.
- Get rid of some custom portmux code from the mimc200 board code. The
old gpio/portmux API couldn't really handle its requirements, but
the new one can.
- Add documentation.
The end result is slightly smaller code for all boards. Which isn't
really the point, but at least it isn't any larger.
This has been verified on ATSTK1002 and ATNGW100. I'd appreciate if
the board maintainers could help me test this on their boards. In
particular, the mimc200 port has lost a lot of code, so I'm hoping Mark
can help me out.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Mark Jackson <mpfj@mimc.co.uk>
Cc: Alex Raimondi <alex.raimondi@miromico.ch>
Cc: Julien May <julien.may@miromico.ch>
Changes since v1:
* Enable pullup on NWAIT
* Add missing include to portmux-pio.h
* Rename CONFIG_PIO2 -> CONFIG_PORTMUX_PIO to match docs
Notice: USB on S3C6400 currently works _only_ with switched off MMU. One could
try to enable the MMU, but map addresses 1-to-1, and disable data cache, then
it should work too and we could still profit from instruction cache.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
DM644x is just one of a series of DaVinci chips that use the EMAC driver.
By replacing all the function names that start with dm644x_* to davinci_*
we make these function more portable. I have tested this change on my EVM.
DM6467 is another DaVinci SOC which uses the EMAC driver and i will
be sending patches that add DaVinci DM6467 support to the list soon.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This function is needed for the new NAND infrastructure. We only need
a dummy implementation though for the NDFC.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a UIC external_interrupt hang if critical or non-critical
interrupt is set at the same time as a normal interrupt is set on UIC0.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Removed Magic numbers from Initialization preload registers
Tested with Kilauea, Glacier, Canyonlands and Katmai boards
About 5-7% improvement seen for LMBench memtests
Signed-off-by: Prodyut Hazarika <phazarika@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
